Micronet-technology IP TELEPHONY GATEWAY SP5052 Manual de usuario

User’s Manual SP5050/SP5052/SP5054 IP Telephony Gateway, FXO Interface Website: http://www.micronet.info

103. Initializing VoIP FXO Gateway Setting 3.1 Gatekeeper Mode (a) Configure VoIP FXO gateway Password (b) Co

11 (a) Configure VoIP FXO gateway Password It is important for the first time user to follow the operation procedure. 1. Power on the VoIP FXO gat

12 (b) Configure VoIP FXO gateway IP Address Use “ifaddr” command to set up VoIP FXO gateway’s IP address and related network information. An exampl

13 Note: mode 1 is for Peer-To-Peer (non-gk) mode, while mode 0 is for GK mode. 2. Configure Phonebook, using “pbook” command. Users can refer to

14 Dynamic IP Address –usr/config$ ifaddr –ipsharing 1 Note: With Dynamic WAN IP Address, a Gatekeeper with a valid IP address for VoIP FXO gate

154. Disconnect Tone Configuration This application note is going to describe the procedures of configuring the disconnect tone on VoIP FXO gateway

16Otherwise it may be released after one minute or lock this LINE permanently. The tone table parameters are shown as follows. LowFreq 480 : Lo

17620/480, take the following procedures. 620/479 620/480 620/481 621/479 621/480 621/481 619/479 619/480 619/481 If the line port of gateway was

185. Command lists 5.1 [help] command Type help or man or ? to list all the available command. usr/config$ ? help help/man/? [command] quit q

19Open debug message will show up specific information while VoIP FXO gateway is in operation. After executing the debug command, it should execute

2 1. INTRODUCTION ...

20Warning: Once users execute flash –clean, all the configurations of VoIP FXO gateway will be cleaned. This can only be executed by user who log in

21 ifaddr -timezone 8 Parameters Usage: -print print current IP setting -ip assigned IP address for VoIP FXO gateway -mask internet

22no answer from 210.54.23.129 usr/config$ ping 192.168.4.121 PING 192.168.4.121: 56 data bytes 64 bytes from 192.168.4.121: icmp_seq=0. time=5. ms

23Please wait for Writing...block 1 Please wait for Writing...block 2 Replay New Greeting Voice?(y/n): Disconnect Tone Analysis : please follow i

243.exit. -------------------------------------------------- Please input function(1~3): 3 Are you sure to EXIT?!(y/n): y usr/config$ 5.11 [pbook

25phone number. Note: <index number> means the sequence number in phone book. If users do not request a specific index number in phone book,

265.12 [pppoe] Display PPPoE related information. PPPoE device information and configuration Usage: pppoe [-print]|[-open]|[-close] pppoe [-dev o

27-idto The duration of two pressed digits in dial mode -eod Digit type of end of dialing. ( 0:No end of dialing, 1:[*] button, 2:[#] butto

281 (Direct In Line Service): This feature must be implemented in a pair of FXO products in Gatekeeper mode and set bureau –table command. In Direct

29value is set to enable all ports. - idto The duration of two pressed digits in dial mode - eod: Digit type of end of dialing. ( 0:No end of dial

3 1. Introduction The Micronet SP5050 Series FXO gateway provides voice/fax service over IP network with H.323 v3 protocol. By connecting to your e

30for response. If the other party cannot respond the message in 10 seconds, VoIP FXO gateway will regard the opposite party as IDLE state and disco

31-gwtype Register as Gateway (1) or Terminal (0) type -ras Gatekeeper RAS port (1024~65535). -range Dynamically allocated port range (15

32-e164 e164 number, which is registered as phone number in gatekeeper. -alias h323 ID, a identification in h323 world for other parties’ recogni

33Usage: gk [-add type1 [[type2]...]] [-delete h323] [-ttl value [-enable 0/1] [-security enable/disable] -print Display the enabled debug fl

34 usr/config$ voice Voice codec setting information and configuration Usage: voice [-send [G723 ms] [G711A ms] [G711U ms] [G729A ms] ] [-volu

35-nscng silence suppression and comfort noise generation setting (1 = ON; 0 = OFF). It is applicable to G.723 codec only. An example is demonstrat

36-rtptype configure TOS type of RTP packets from 0 to 7 -rtcptype configure TOS type of RTCP packets from 0 to 7 -sigdelay configure signa

37 -t38 T.38(FAX) enabled/disabled. -fstart Fast start enabled/disabled. -tunnel H245 Tunneling enabled/disabled. -h245fs H245 separate cha

38 -enable Enable PSTN Grouping -disable Disable PSTN Grouping -number Set number of divided groups -pattern Set number of members

39 -table Set Hot line/Line To Line information. (Port range: 1~2) Note: Hotline feature should be used together with: $sysconf -service 2

4 Management Features: - Console port: RS-232C port - TELNET - HTTP Brower (e.g. Internet Explorer) 1.2 Appearance Front panel: The LED light pr

405.22 [prefix] command This function can do digits replacement of incoming call from IP side or PSTN side. usr/config$ prefix Prefix setting inf

41 -dspcore update DSP kernel code(optional) -dspapp update DSP application code(optional) -rbpcm update RingBack Tone PCM file(optiona

42asking for pincode. -s to specify TFTP server’s IP address when upgrading ROM files. -f to specify the target file name, which will replace the

436. Upgrade the VoIP FXO gateway VoIP FXO gateway supports remote download via TFTP for updating the new ROM file. Regarding new version release,

44-method to decide using TFTP or FTP as file transfer server. “0” stands for TFTP, while “1” stands for FTP. -ftp if users choose FTP in above it

45 Appendix: Web configuration Web management simple user guide The initial version for HTTPD web management interface provides user to configur

46Step 2. Input the login name and password  Login name: root / administrator  Password: None (just press Enter in default value) Th

47Step 3. Start configure Most of all commands displayed in console / telnet are transfer to web interface. The most important commands are Network

48 1.2 H323 Information z Mode: Select GK mode or Peer-to-Peer mode z Gatekeeper IP Address: Set Gatekeeper IP Address z Gateway Type: Set Regi

49 1.3 System Config z Keypad Type: Select different DTMF Keypad Type (For Advanced User) z Dial Plan: Set DTMF digit limitation (0 is for any dig

5 PIN 1, 2: Transmit PIN 3, 6: Receive COM: RS232 console port (9-pin Male connector, as the same as the computer). Male connector (as the s

50 1.4 Voice Setting (For Advanced User) z Frame Size: It got wrong order with “Codec Priority”. Select the Codec Priority. (For Advanced User) z

51 1.5 Phone Pattern (For Advanced User)

52 1.6 Support Functions (Both side must support) z T.38: En abl e f or T.38 FA X z Fast Start: Enable to do Fast Start z H.245 Tunneling: Ena

53 1.7 Phone Book (For Peer-to-Peer mode only) Input the Name, IP Address and E.164 No. for the destination device. Please Note: The E.164 No. w

54 1.8 Type Of Service Adjust the parameter in IP Header for router identity purpose. If the version has PPPoE function, ToS is not available.

55 1.9 Hot Lines Select HOST Port and set Destination Address. The Remote Number is subject to the Destination’s configuration.

56 1.10 PPPoE

57 1.11 Password First select login name as root or administrator, then enter current password , new password and confirm new password again.

58 1.12 ROM Upgrade z TFTP Server IP Address: Set TFTP server IP address z Target File name: Set file name prepared to upgrade z Method: Select

59 1.13 flash Clean Press CLEAN will clean all configurations of Gateways and reset to factory default value. Once execute this function, user mus

6 2. System Operating Procedure 2.1 System Requirement 2.2 Telephone Line Requirement 2.3 IP Environment Setting START END 2.4 Hyper Terminal S

60 1.14 Commit Data After configuration, user has to commit data then reboot machine. It is an important step after every configuration.

61 1.15 Reboot System After commit configuration, user has to REBOOT device. It is an important step after every configuration.

72.1 System Requirement 1. One PC (a) Pentium 100 or above, 64 MB DRAM, Windows 98 or above. (b) Network card (RJ-45) & COM port 2. One standa

8 2. Define a name such as ‘SP5050 Gateway’ for this new connection. 3. After pressing OK button, the next window popping up is necessary to

9 Note: Some connection failed is derived the PC COM Port. If user cannot open the com port, for example com 1, please try another com port, ex.com