Micronet-technology Network Device RAIDBank4 Manual de usuario Pagina 26
- Pagina / 66
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
RAIDBank4 Owner’s Manual
26
5.7 Host Channel NCQ Setting
The RAIDBank4 supports Native Command Queuing (NCQ) over the eSATA host connection.
The NCQ algorithms allow I/O operations to be performed out of order to optimize performance.
Since different host bus adapters have some compatibility differences in NCQ implementation,
The default setting on this option is Disable for better compatibility. To enable NCQ, choose
the option that matches your eSATA host bus adapter:
•ESB2/MACPro/Siliconlimage:IntelESB2,MACPro,MicroNet,andSiliconImagebasedadapters
•ICH:IntelICHseriesbasedadapters
•Marvell6145:Marvell6145basedadapters
•nVidia:NvidianForcebasedadapters
5.8 HDD Read Ahead Cache
Enabled by default. Please do not change this setting unless instructed by MicroNet’s Technical Support.
5.9 Staggered HDD Spinup control
The RAIDBank4 employs a staggered disk mechanism startup sequence to minimize power supply
strain. Please do not change this setting unless instructed by MicroNet’s Technical Support.
5.10 HDD Idle Spindown Control
The RAIDBank4 can automatically spin down disks that haven’t been accessed for a certain
amount of time to reduce power consumption. This value is used to determine idle time
before spinning down the disk(s).
5.11 Empty tray LED Control
(ON or OFF) If this option is selected, the disk error LED will light on a slot without a disk.
5.12 HDD SMART Status Polling
The RAIDBank4 reads and reports the SMART (Self-Monitoring, Analysis, and Reporting Technology)
status of each disk drive mechanism. This option is enabled by default, and should not be disabled
unless instructed by MicroNet’s Technical Support.
5.13 Disk Capacity Truncation Mode
Disk Truncation is used to decrease disk usable space for compatibility purposes. Please do
not change this setting unless instructed by MicroNet’s Technical Support.
5.14 Serial Port Configuration
The RAIDBank4 has provisions for an RS232 host management connection. In order to use the
RS232, a special cable has to be used (not included)- consult your authorized Micronet reseller
for more information. To set or change the RAIDBank4 communications port configuration,
Scroll to the “Terminal Port Configuration” selection and press ENT. The communications port
configuration defaults are 115200 Baud., 1 Stop bit operation. The baud rate (1200-115200)
and stop bits (1,2) are user selectable. Handshaking and parity are fixed at none.
5.15 Reset Controller
To reset the RAIDBank4, select “Reset Controller” and then
press ENT. Press ENT at the confirmation screen to reset
the controller.
IMPORTANT: Controller Reset
can only be performed if no host
or drive activity is present.
!
3-RAID Control-LCD
- Owner’s Guide 1
- FCC Compliance Statement 2
- Warranty 3
- RAIDBank4 Owner’s Manual 4
- Table of Contents 5
- 1-Getting Started 10
- 2-Understanding RAID 13
- 3-RAID Control-LCD 18
- 4-RAID Control-Web Interface 29
- 5-Host Computer Setup 45
- 6-Troubleshooting 47
- A-Getting Help 52
- B-RAID Level Comparison Table 53
- C-Terminal Session Setup 54
- D-Glossary 57
- E-Product Specifications 64
- MicroNet Techology 66
- 19260 Van Ness Ave 66
- Torrance, CA 90501 66
Relacionado con productos y manuales para Hardware Micronet-technology Network Device RAIDBank4
(10 paginas)Basler-electric BE1-700 manuales
Manuales del propietario y guías del usuario para Relé Basler-electric BE1-700.
Ofrecemos 1 manuales en pdf Basler-electric BE1-700 para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales